Guide
Remove dust and distractions with Spot Removal
Paint out dust spots, specks and thin lines such as a wire in Radiant Photo, then fine-tune or delete any fix.
Draft: not yet checked against the release
Spot Removal in Radiant Photo paints out dust, specks and thin lines, such as a sensor spot in the sky or a stray wire. Click once for a small spot, or drag along a longer line, and Radiant Photo picks a clean source from your own photo to cover it. You can move, change or delete any fix.
Remove a dust spot with one click
- Open the photo in Radiant Photo.
- Press Q, or click the Spot Removal tab in the right rail. You can also open the View menu and choose Tools > Spot Removal. Opening the page turns the tool on.
- Set Brush Size so the round brush covers the spot. Press ] to make the brush larger and [ to make it smaller.
- Click the spot. Radiant Photo places a dab and picks a clean source for it.
- Repeat for each spot. Each fix gets its own row in the panel's list.
When you're done, press Esc to put the tool away. If a source is showing, the first press hides it and the second puts the tool away.
Tip
Each dab is one Undo step. If a fix looks wrong, undo it and click again.
Paint out a wire or a line
A longer defect needs a stroke instead of a dab.
- Drag along the defect. The whole stroke is one fix, marked Stroke in the list.
- For a straight line, such as a wire, hold Shift and drag.
- If the line bends, Shift-click where the next straight part ends. This adds a straight segment to the last fix.
Tip
Softness sets how soft the edge of the next fix is. Press ⌥[ for a softer edge and ⌥] for a harder one. The brush shows two rings: full strength ends at the solid ring, and the soft edge fades out to the fainter one.
Choose Heal or Clone
Under Brush, choose the mode for new fixes.
- Heal blends the source texture into the spot. It's the default, and the best choice for most dust.
- Clone copies the source pixels straight over the spot. Use it when you need an exact copy. Clone copies only from a source you set, so ⌥-click the good pixels first (Alt-click on Windows), as Pick the source yourself shows below. Without a source, a Clone stroke places nothing.
To change one fix only, select it and use its own Heal and Clone switch.
Tip
Dust on a plain sky? Set Blend Mode under Brush to Lighten for dark dust on a light sky, or Darken for a light speck on a dark sky. The fix then changes only pixels darker than it (with Lighten) or lighter than it (with Darken), so most of the sky around the dust stays as it is.
Pick the source yourself
In Heal, Radiant Photo picks a source for each fix. You can set the source yourself before you paint. It applies to the fixes you paint after you set it. To change the source of a fix you already made, see Adjust or delete a fix below.
- ⌥-click the photo where the good pixels are (Alt-click on Windows). A crosshair marks the source, and the panel shows Source set.
- Paint the defect. The source keeps the same distance from the brush as you paint more fixes.
- ⌥-click again to choose a new source, or click Clear Source to go back to automatic sources.
Tip
With a source set, hold ⌥⇧ (Alt+Shift on Windows) to see its pixels inside the brush ring, and drag to line them up. To start every stroke from the same point, turn off Aligned.
Adjust or delete a fix
Click a fix's pin on the photo, or its row in the panel, to select it. Its source shows as a dashed circle, joined to the fix by a line.
- Drag the fix's pin to move the fix, or drag the source's pin to move the source.
- To let Radiant Photo pick a clean source again for a Heal fix, click Auto Source. A Clone fix copies only from the source you set, so drag its source's pin instead.
- Adjust Radius, Feather and Opacity to fine-tune the fix.
To delete fixes, ⌥-drag a box around them (Alt-drag on Windows). The fixes inside turn red, and letting go deletes them in one Undo step. A plain ⌥-click sets the source instead. To start again, click Clear Spot Removal. It removes every fix on this photo in one Undo step.
Tip
Show Pins sets when pins appear on the photo. Press ⇧H (Shift+H on Windows) to step through its choices, such as Never.
Copy the fixes to other photos
- On the photo with the fixes, click Copy Settings…, the sliders icon in the bottom bar. The chooser opens.
- Tick Spot Removal. It starts unticked.
- Click Copy in the chooser. It copies with your choices and closes the chooser.
- Open another photo and click Paste.
Important
With Add, the default, the copied fixes join the other photo's own. Replace removes its own fixes first. With Add, a copied fix that lands on one the photo already has is skipped.
For every control, range and key, see Spot Removal in the Radiant Photo manual. For more ways to copy and sync, see Copying and syncing settings.
What it is What Spot Removal is and why it matters
The controls in this guide
Each one opens its page in the manual.