Radiant Imaging Labs

Guide

Read your exposure and color with scopes

Use the histogram, the scopes and color samplers to check exposure and color by numbers, not only by eye.

Draft: not yet checked against the release

Level
Intermediate
Time
15 min
Apps
Radiant Raw 1.0Radiant Photo 2.5

The histogram and scopes show how the light and color in your photo are spread out, so you can judge exposure and color by numbers, not only by eye. In this guide you check a photo for clipped shadows and highlights, pick the scope that answers your question, keep a scope in view while you edit, and measure single colors with samplers. The steps work in Radiant Raw and Radiant Photo, and the guide notes where the two differ.

Check exposure with the histogram

The histogram sits at the top of the right panel. If you don't see it, click Histogram at the top of the right rail in Radiant Photo, or Histogram in Radiant Raw.

  1. Look at the shape. Shadows are on the left, midtones in the middle and highlights on the right.
  2. Check both edges. A pile-up against the left or right edge means detail is clipped to pure black or pure white.
  3. Press J to paint the clipped pixels on the photo. In Radiant Photo, clipped shadows show in blue and clipped highlights in red.

In Radiant Raw, J turns the warning on or off. You can also click the left clipping capsule to show crushed shadows, and the right one to show blown highlights.

Tip

Turn on Logarithmic histogram scale to lift small counts in the shadows and highlights so you can see them. In Radiant Photo it's in the Histogram panel, once Pro histogram is on. In Radiant Raw, turn on PRO (Pro histogram) in the histogram's header, then click the LOG pill (Logarithmic histogram scale) beside it.

The clipping colors are set in Settings > Color in Radiant Photo, and in Settings > Color > Clip warning colors in Radiant Raw.

Fix the tones from the histogram in Radiant Raw

With PRO on, the histogram in Radiant Raw is split into Blacks, Shadows, Exposure, Highlights and Whites. Each band is a shortcut to the Tone slider of the same name.

  1. Drag a band sideways to adjust that Tone slider. You don't need to open Tone.
  2. Watch the histogram as you drag.
  3. To reset a band, double-click it.

Choose the scope that answers your question

ScopeShowsUse it to
HistogramHow many pixels sit at each brightnessCheck exposure and clipping
WaveformBrightness across the width of the photo, left to rightSee where in the frame the highlights and shadows are
ParadeThe waveform split into red, green and blueSpot a color cast in the whites or the blacks
VectorscopeHue around the circle, saturation out from the centerCheck saturation and skin tones

To switch scopes in Radiant Photo:

  1. Turn on Pro histogram in the Histogram panel.
  2. Open the Scope menu and choose a scope.

In Radiant Raw, turn on PRO in the histogram's header, then click the scope's title, which reads Histogram, and choose Waveform, Parade or Vectorscope.

Check skin tones in Radiant Photo

  1. Choose Vectorscope from the Scope menu.
  2. Choose Scope Settings… from the same menu.
  3. Make sure Skin-tone line is on.
  4. Compare the skin tones in the scope against the line.

Note

The settings change with the scope you're looking at. Reset to Defaults puts them back the way they came.

Keep a scope in view while you edit

You can draw a scope over the photo, so you can watch it while you work full screen. You can also open the scopes in a window of their own, which can be much larger than the panel.

Show scopes on the photo

  1. Press ⌃⌘G (Ctrl+Shift+G on Windows). In Radiant Raw you can also choose Show Scopes on Photo from the scope's title menu, with PRO on.
  2. Choose Band, Full frame or Corner. In Radiant Photo this setting is called Placement. There, a band runs across the bottom, a full frame sits over the photo, and a corner card can be moved and resized.
  3. Set the Opacity, and the Band height if you chose a band.

In Radiant Raw, Position can also put the scope Below the photo instead of over it.

Tip

In Radiant Raw, when you zoom in, a band measures only the Visible area. In Radiant Photo, a tag on the scope says what it measures: Whole photo, the Visible area when you're zoomed in, or Proof while you soft proof.

Open the Scopes window

  1. Press ⌃⌘W (Ctrl+Shift+U on Windows). In Radiant Raw you can also choose Show Scopes Window from the scope's title menu, with PRO on.
  2. Choose a Layout, such as Two, side by side, and pick a scope for each pane.
  3. Drag the window's header to move it, and drag the corner grip to resize it. Double-click the header to fill the canvas, and double-click it again to go back.

Link with Photo is on by default, so the window measures the photo you're editing.

Measure a color with samplers

A sampler is a measuring point that stays on the photo and shows its color as you edit. You can place up to ten.

  1. Press I to turn on the Color Sampler.
  2. Click the photo where you want to measure. A numbered marker appears.
  3. Click again to add more points.
  4. Read the values under Samplers. In Radiant Photo they're in the Histogram panel. In Radiant Raw they're under Samplers, below the histogram, with Pro histogram on. Turning the sampler on turns Pro histogram on.
  5. Move a slider and watch the numbers change.

Click Clear All to remove every sampler.

Tip

Put one sampler on something that should be neutral, such as a gray card or a white shirt. If its red, green and blue values are equal, the color is neutral.

Note

In Radiant Photo, samplers are a measuring tool, not an edit. They aren't saved with the photo, and closing the photo removes them.

What it is What Scopes is and why it matters